</a>PFC" title="PFC">PFC" title="PFC">PFC開關電源控制器,具有升壓或反激轉換器模式.器件中的PFC電路在各種線路/負載范圍內提供高PF,低THD和穩定的DC總線調整,具有逐個周期的過流和輸出過壓保護,主要用在開關電源,電子鎮流器和LED驅動器.本文介紹了IRS2500主要特性, 功能框圖, 典型應用電路以及PFC預調整電路圖, 80W PFC電路圖
及其材料清單.
The IRS2500 is a fully integrated, fully protected PFC SMPS control IC designed to drive Boost or Flyback switching regulators providing high power factor. Typical applications are PFC pre-regulators for SMPS and electronic ballasts for fluorescent or HID lighting as well as single stage Flyback converters widely used in low power LED drivers. The IRS2500 is pin compatible with most industry standard critical counduction or transition mode PFC control IC with additional improvements to increase performance. The PFC circuitry provides high PF, low THD and stable DC bus regulation over a wide line/load range. The IRS2500 protection features include cycle by cycle over-current protection and output over voltage protection.
IRS2500主要特性:
• PFC Control IC
• Boost or Flyback Converter Modes
• Critical-conduction / Transition mode operation
• Over-current protection
• Static and Dynamic DC bus overvoltage protection
• Micropower startup (<50μA)
• Low quiescent current (2.5mA)
• Latch immunity and ESD protection
• Wide range PFC for universal AC line input
• Low THD
• Open load Over voltage protection
• Noise immunity
IRS2500典型應用:
• Switched Mode Power Supplies
• Electronic Ballasts
• LED Drivers
圖1.IRS2500功能框圖
圖2.IRS2500典型應用電路
Many offline applications require power factor correction circuitry in order to minimize transmission line losses and stress on electrical generators and transformers created by high harmonic content and phase shift. Appliances often incorporate switching power supplies (SMPS) which include capacitive filter circuitry followed by a bridge rectifier and bulk capacitor supplying a load.
Without power factor correction circuitry a SMPS draws a high peak current close to the line voltage peak and almost no current over much of the cycle, resulting in a power factor of around 0.5 and a high total harmonic distortion.
Power factor correction circuitry is added which enables the appliance to draw a sinusoidal current from the AC line with negligible phase shift and very low harmonic distortion. This allows optimization of the load seen by the power grid such that power can be supplied without creating additional conductive losses in transmission lines or additional burden on transformers and generators. Costs to electricity providers are therefore reduced, which are hopefully passed on to the consumer.
Although not explicitly specified in standards such as IEC 61000-3-2 relating to power factor and line current harmonics, it is generally a requirement for the total harmonic distortion (THD) of the line input current supplying a PFC pre-regulator to be as low as possible. As is normally the case a tradeoff exists between cost and performance where more expensive high end products rated at higher power typically incorporate active power factor correction circuits, while low cost passive circuits often suffice in cheaper consumer products.
This is a market trend in power supplies used in a variety of appliances as well as electronic lighting ballasts for Fluorescent, high intensity discharge (HID) lamps and LED lighting.
For a product incorporating active power factor correction a THD of less than 20% over a wide input voltage range, normally 100VAC to 305VAC is expected.In many cases THD can be less than 10% over much or all of this voltage range.
The IRS2500 based PFCpre-regulator does not provide galvanic isolation of the output from the line input. Therefore if the system is supplied directly from a non-isolated input, an electrical shock hazard exists.The DC output voltage is highenough to produce a potentially lethal electrical shock!
It is recommended that for laboratory evaluation that the IRS2500PFC board be used with an isolated AC or DC input supply. The IRS2500 series Boost topology is suitable only for front end applications where isolation is either not necessary or provided elsewhere in the system.
圖3.IRS2500 PFC預調整電路圖
圖4.IRS2500 80W PFC電路圖
80W PFC電路材料清單(BOM):
詳情請見:
http://www.irf.com/product-info/datasheets/data/irs2500spbf.pdf
和
http://www.irf.com/technical-info/appnotes/an-1173.pdf
及其材料清單.
The IRS2500 is a fully integrated, fully protected PFC SMPS control IC designed to drive Boost or Flyback switching regulators providing high power factor. Typical applications are PFC pre-regulators for SMPS and electronic ballasts for fluorescent or HID lighting as well as single stage Flyback converters widely used in low power LED drivers. The IRS2500 is pin compatible with most industry standard critical counduction or transition mode PFC control IC with additional improvements to increase performance. The PFC circuitry provides high PF, low THD and stable DC bus regulation over a wide line/load range. The IRS2500 protection features include cycle by cycle over-current protection and output over voltage protection.
IRS2500主要特性:
• PFC Control IC
• Boost or Flyback Converter Modes
• Critical-conduction / Transition mode operation
• Over-current protection
• Static and Dynamic DC bus overvoltage protection
• Micropower startup (<50μA)
• Low quiescent current (2.5mA)
• Latch immunity and ESD protection
• Wide range PFC for universal AC line input
• Low THD
• Open load Over voltage protection
• Noise immunity
IRS2500典型應用:
• Switched Mode Power Supplies
• Electronic Ballasts
• LED Drivers
圖1.IRS2500功能框圖
圖2.IRS2500典型應用電路
Many offline applications require power factor correction circuitry in order to minimize transmission line losses and stress on electrical generators and transformers created by high harmonic content and phase shift. Appliances often incorporate switching power supplies (SMPS) which include capacitive filter circuitry followed by a bridge rectifier and bulk capacitor supplying a load.
Without power factor correction circuitry a SMPS draws a high peak current close to the line voltage peak and almost no current over much of the cycle, resulting in a power factor of around 0.5 and a high total harmonic distortion.
Power factor correction circuitry is added which enables the appliance to draw a sinusoidal current from the AC line with negligible phase shift and very low harmonic distortion. This allows optimization of the load seen by the power grid such that power can be supplied without creating additional conductive losses in transmission lines or additional burden on transformers and generators. Costs to electricity providers are therefore reduced, which are hopefully passed on to the consumer.
Although not explicitly specified in standards such as IEC 61000-3-2 relating to power factor and line current harmonics, it is generally a requirement for the total harmonic distortion (THD) of the line input current supplying a PFC pre-regulator to be as low as possible. As is normally the case a tradeoff exists between cost and performance where more expensive high end products rated at higher power typically incorporate active power factor correction circuits, while low cost passive circuits often suffice in cheaper consumer products.
This is a market trend in power supplies used in a variety of appliances as well as electronic lighting ballasts for Fluorescent, high intensity discharge (HID) lamps and LED lighting.
For a product incorporating active power factor correction a THD of less than 20% over a wide input voltage range, normally 100VAC to 305VAC is expected.In many cases THD can be less than 10% over much or all of this voltage range.
The IRS2500 based PFCpre-regulator does not provide galvanic isolation of the output from the line input. Therefore if the system is supplied directly from a non-isolated input, an electrical shock hazard exists.The DC output voltage is highenough to produce a potentially lethal electrical shock!
It is recommended that for laboratory evaluation that the IRS2500PFC board be used with an isolated AC or DC input supply. The IRS2500 series Boost topology is suitable only for front end applications where isolation is either not necessary or provided elsewhere in the system.
圖3.IRS2500 PFC預調整電路圖
圖4.IRS2500 80W PFC電路圖
80W PFC電路材料清單(BOM):
詳情請見:
http://www.irf.com/product-info/datasheets/data/irs2500spbf.pdf
和
http://www.irf.com/technical-info/appnotes/an-1173.pdf
本站內容除特別聲明的原創文章之外，轉載內容只為傳遞更多信息，并不代表本網站贊同其觀點。轉載的所有的文章、圖片、音/視頻文件等資料的版權歸版權所有權人所有。本站采用的非本站原創文章及圖片等內容無法一一聯系確認版權者。如涉及作品內容、版權和其它問題，請及時通過電子郵件或電話通知我們，以便迅速采取適當措施，避免給雙方造成不必要的經濟損失。聯系電話：010-82306118；郵箱：aet@chinaaet.com。